Plough Book Sales

Online Catalogue last updated 25th of June 2012


Tire Pump Plans

THE ULTIMATE TIRE PUMP..., Plus some good info on making springs

How would you like to be able to make a really superior tire pump?

You can, from the plans offered here.

Guy Lautard writes:

Pumping up tires by hand is not the most fun thing to do. But if you ever need to do it, which would you prefer to do it with a lousy one that wastes a large percentage of your effort (or may even break, leaving you without a functioning tire pump, and possibly injure you as well), or a very efficient pump that you can make yourself, that does not leak, doesn't waste your energy, and is tougher than the best factory-made tire pump money can buy?

As I understand it, the U.S. military uses a tire pump that has been made for them unchanged for the past 65 years. I had been considering getting one of these pumps not because I have frequent use for a tire pump, but because I do need one once in a while, and because, given that I do, it would appeal to me to have a really good one.

Then one day, entirely by accident, I spotted a very cool looking tire pump, and naturally, since I had tire pumps on my mind at the time, it caught my eye. Because of my interest, the guy who'd made it told me about it, and even partially dismantled it to show me some of its details.

The piston in this pump is more efficient than the usual leather cup seal. Leather is almost ideal for the purpose, because it is very durable, and it retains oil, but it is porous, so it wastes some of your effort in unavoidable leakage. This guy's piston solves this problem 100%. It also incorporates a simple but efficient shop-made air inlet valve, so that when you raise the plunger rod, new air is let into the pump very readily. When you start your compression stroke, the inlet valve closes, with no leakage, so the new batch of air gets compressed and sent to your tire, rather than leaking back past the inlet valve or a porous cup leather.

All the parts in this guy's pump were either cheap to buy, or were readily made by any machinist from easy-to-get materials.

A standard brass reducer fitting at the base of the pump is bored out to hold a simple, slick, and very efficient shop-made check valve. Immediately downstream from the check valve/reducer fitting is a T-fitting carrying an oil filled pressure gauge.

Most hand operated tire pumps are very easily knocked over, because they are tall, top-heavy and have a small base. Not this one, it has a base on it that overcomes this problem. If you give it a bump, it cockles around a little, and returns to upright. Note, however, that if you want to stow the pump in your vehicle, you can remove this base very readily by undoing one bolt.

In short, this guy had made a real serious tire pump.

He loaned it to me, and gave me a free hand to dismantle it and measure everything. I did so, and when I had figured out the last detail, I worked up good drawings, and then started gathering materials to make one for myself. I think I am going to have the best tire pump imaginable.

I also got his ok to offer my drawings and how-to notes for sale, so you too can build a really good tire pump, it's easy to do, you'll learn some interesting things along the way, and when you're done, you'll have a tire pump that probably even beats the mil-spec one Uncle Sam uses.

A BONUS:

Some info on making Springs

Also included with these plans is some excellent info on spring making, including how to calculate mandrel diameter required to produce a coil spring of a given size, using wire of a given size.

Code No. 012021, $29.00

This item is listed under the following subjects:

Workshop  
Home Page   |  Contents Page (Catalogue)   |  Information Pages   |  What's New   |  Links   |  Search Entire Site   |  Order Form

Plough Book Sales, P.O. Box 14, Belmont, Vic. 3216, Australia
Phone: 03 52661262 (International +61 3 52661262)
FAX: 03 52662180 (International +61 3 52662180)
E-mail: Stephen@ploughbooksales.com.au
© 2001-2008, Plough Book Sales